Replacing Lock on uPVC Door
To replace the lock, you need to first remove the screw holes and handle. This is usually easy to accomplish.
Next, locate the screw that holds in the lock barrel. This screw is typically different in colour from the other screws, and is located on the edge the lock faceplate.
Take the Cylinder off
To change the lock on your upvc doors first, you must take off the cylinder that is currently in use. This is a relatively simple procedure that can be done in about 30 minutes. All you require is an ordinary screwdriver. You'll need the Euro fixing screw for the cylinder that is typically located on the inside edging of the door, just next to the lock cylinder. The screw is usually colored differently from the other screws and is easy to identify. Remove this screw, and store it safely.
After removing the cylinder, you can begin to remove the handle. To do repairmywindowsanddoors.co.uk , you will need to open the door wide enough that you can observe the inside edge of the door and the side of lock faceplate.
Begin with a screwdriver to take off the screw that is holding the handle to the door. Once the screw is removed you should be able to pull the handle towards you and the rest of the mechanism should be removed from the door.
If you are having trouble getting the handle off, you may need to unscrew the screw holding it to the stud of the door frame. You can make use of a screwdriver or a drill to remove the handle. Be cautious not to pull or cross-thread it.
If you are about to replace your cylinder, be sure that it is the correct size for your door. Cylinders are measured based on two points: (a), the distance from the center of the Fixing Screw to the bottom of cylinder and (b) the distance between the hole of the keyhole and edge of the lockplate.
Take the handle off
The good news is that if your upvc handle becomes stiff, floppy, or loose, it is an easy problem to repair. The cause is usually due to wear and tear on the cylinder or internal components of the multipoint lock which are located inside the door between the handle and the frame. The weather, the heavy use or ageing can cause upvc locks to wear. This can lead to issues with the closing and locking mechanisms of the door.
The cylinder can become worn and make it difficult to turn the key. The lock can also become stiff, causing the handle to loosen. The cylinder can be replaced, and this is a simple process. It is possible to do this yourself, though some understanding of how the mechanism operates is required. The first step is to take off the handle, which will allow you to access the valve and replace it with a brand new one.
You will need a screwdriver, and a measuring tape for this. It is crucial to know the exact measurements of your cylinder, to be able to purchase a replacement that fits. The cylinder allows you to lock the door of your upvc. It is important to order a replacement that is exactly the same size.
To remove the old cylinder, you'll have to remove the screws that hold it in place. Be cautious not to pull out the screws, as this could make it difficult to remove the screws in the future. After the screws have been removed, the cylinder will come out easily.
Remove the Lock Barrel
uPVC doors are constructed with extremely durable materials and are designed to keep your home safe and secure. They are available in various designs and colors to match any style. These doors are also maintenance-free and thermally efficient. However, they aren't without their disadvantages. The locking point, also known as a barrel lock, could become faulty in time and requires to be replaced. It's a simple procedure, but there are some things to know before beginning.
To access the screw holding the lock cylinder, you'll need to remove your door handle. It's typically a different color from the other screws and is situated at the edges of the door, just where the keyhole is located. Take the screw off and store it in a safe location. Slide the handles off both the inside and outside of the door. Make sure you take your time and not move too fast, as it may harm your uPVC door.
Once you have removed the handles using a screwdriver, disconnect the screws that are holding them to the frame of the door. This will give you better access to the pins holding the cylinder in place. You can then pull and wiggle the cylinder to see if this will loosen it. Once it comes loose, pull it towards you and then out the socket.
After you have removed the old lock cylinder it is important to replace with a brand new one that includes anti-snap protection as well as anti-bump. It is recommended to have an expert locksmith do this for you, but you can do it yourself with the appropriate tools. This is a fairly simple job that should take only about five minutes to complete.
Install the New Cylinder
A upvc lock can be damaged or broken in a variety of different ways. For instance the cylinder could have become damaged or no longer work as it should. Whatever the reason for changing your upvc lock, it is important that you choose the correct size replacement. If the wrong lock is installed, your upvc doors may be more susceptible to the 'lock snapping method which is the reason for 25 percent of burglaries.
It is essential to put in the proper cylinder. The process is easy and takes just five minutes. You will require an instrument to remove the screws that are attached to the faceplate on the handle and the cylinder. Once the removal is completed, it is a simple task to switch them.
Before you begin, make sure that the handle is open and you have full access to the inside edging of the door as well as the handle's faceplate which holds the lock cylinder. This will allow you to easily remove the lock cylinder from the handle without having to move it, and expose the inside of the frame.
Then, remove the old cylindrical device and measure it. You'll need to know the length of the cylinder and the measurement of the cylinder that moves to lock or open the door. This will help you to find a replacement that is similar in size or smaller. This is the most crucial aspect of the whole procedure. The cylinder should be flush with the handle, and not protrude more than 5mm from it.
Install the Handle
It is not unusual for a door lock made from upvc to become jammed and this can be caused by a broken part inside the case which controls the bolts that retract into the strike or keep plate. This can often be solved by adjusting the Allan key that is located beneath the hinges. However, this could sometimes cause too much stress on the components within the centre casing and it is advised to seek out an expert.
During the process of changing it is crucial to have quick and easy access to both sides of the handle and having the right tools. It is also a good idea to prop the door open so it doesn't close during the process.
The first step is to loosen the screws that hold the handle in position with the screwdriver. Once the screws are loosen you can take off the handle. After the cylinder and handle have been removed, it's now time to put in the new handle. Ensure that the new handle is of the correct size for your existing cylinder and hole in the center. Verify the length of the spindle on the lever you are currently using to determine this. Make sure that the screw fix centre on the handle is the same as the screw fix centre of your existing hole centre or cylinder.
Replacement handles from Fab and Fixed come in different styles and are designed to last. These handles are perfect for those looking to upgrade their Upvc handle and improve home security. Having the right handle will ensure that your home is secure and safe and will not be a target for burglars to break into.